www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 1 of 9 s pec n o : ? ? s s p p e e c c i i f f i i c c a a t t i i o o n n customer product ? saw filter model no hdf 1575 a smd - 6 m arking ? hdf6g09 prepared checked approved ? d a t e 200 6 - 5 - 1 1 ??? shoulder electronics limited ?? c ustomer received: c hecked ? approved d ate
saw filter hdf 1575a s - 6 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 2 of 9 ?? history record date spec . no . ?? part no . ??? customer no . modi fy content ? remark
saw filter hdf 1575a s - 6 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 3 of 9 1. features gps applications usable bandwidth of 2 mhz no impedance matching require for operation at 50 . single - ended operation 2. package dimension marking hdf 6g09 hd: brand f : filter 6 : smd - 6 g09: no.
saw filter hdf 1575a s - 6 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 4 of 9 3 . marking 2.1 color: black or blue 2.2 1575: center frequency(mhz) 4 .performance 4 .1application low - loss saw filter of cordless system. center frequency:157 5.42 mhz 4.2 maximum rating operation temperature range - 4 0 to + 85 storage temperature range - 40 to +85 power handling capability 10 dbm 4.3 electronic characteristics
saw filter hdf 1575a s - 6 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 5 of 9 parameter symbol conditions min typ. max. unit center frequency 1575.42 mh z operational bandwidth f op 1574.22 1576.62 mhz insertion loss il in f op 1.5 2.5 db amplitude variation av in f op 0.2 0.5 db vswer swr in f op 1.3 2 rejectiona wrt 0 db rj1 0.3 ~ 700 mhz 40 45 db in top rj2 700~1460mhz 37 40.5 db rj3 1460~1470mhz 45 50 db rj4 1470~1525mhz 37 43 db rj5 1525~1535.42mhz 20 25 db rj6 1615.42~1620mhz 25 35 db rj7 1620~1650 mhz 45 50 db rj8 1650~3000 mhz 40 45 db i/p & o/p impedance zin/zout unmatched 50 ohm notes : 1) all specifications are based on the matching schematic shown below, measured by agilent network analyzer and full 2 port calibration. 2) electrical margin has been built into the design to account for the variations due to temperature drift and manufacturing tolerances 3) a ll attenuation measurements are measured relative to insertion loss 4.4 test circuit
saw filter hdf 1575a s - 6 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 6 of 9 5 . environmental characteristics 5 - 1 temperature cycling subject the device to a low temperature of - 40 for 30 minutes. following by a high temperature of + 8 5 for 5 minutes and a higher temperature of +85 for 30 minutes. then release the device into the room conditions for 1 to 2 hours prior to the me a surement. it shall meet the specifications in 4.3 . 5 - 2 resistance to solder heat submerge the device terminals into the solder bath at 260 5 for 10 1 sec. then release the device into the room conditions for 4 hours. it shall meet the specifications in 4.3 . 5 - 3 solderability submerge the device term inals into the solder bath at 245 5 for 5s, more than 95% area of the soldering pad must be covered with new solder. it shall meet the specifications in 4.3 . 5 - 4 mechanical shock drop the device randomly onto the concrete floor from the he ight of 1 m 3 times. the filter shall fulfill the specifications in 4.3 . 5 - 5 vibration subject the device to the vibration for 2 hour each in x,y and z axes with the amplitude of 1.5 mm at 10 to 55 hz. the filter shall fulfill the specifications in 4.3 . 6 . remark 6 .1 static voltage static voltage between signal load & ground may cause det e rioration &destruction of the component. please avoid static voltage. 6 .2 ultrasonic cleaning ultrasonic vibration may cause det e ri oration & destructi on of the component. please avoid ultrasonic cleaning 6 .3 soldering only leads of component may be soldered. please avoid soldering another part of component.
saw filter hdf 1575a s - 6 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 7 of 9 7 . packing 7 .1 dimensions (1) carrier tape: figure 1 (2) reel: figure 2 (3) the p roduct shall be packed properly not to be damaged during transportation and storage. 7 .2 reeling quantity 1000 pcs/reel 7?? 3000 pcs/reel 13?? 7 .3 taping structure (1) the tape shall be wound around the reel in the direction shown below. (2) label device name user product name quantity lot no. (3) leader part and vacant position specifications.
saw filter hdf 1575a s - 6 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 8 of 9 8 . tape specifications 8 .1 tensile strength of carrier tape: 4.4n/mm width 8 .2 top cover tape adhesion (see the below figure) (1) pull off angle: 0~15 o (2) speed: 300mm/min. (3) force: 20~70g [figure 1] carrier tape dimensions [unit:mm] w f e p0 p1 p2 d0 d1 t1 t2 a b 12.00 0.30 5.50 0.10 1.75 0.10 4.00 0.10 4.00 0.10 2.00 0.10 ?1.50 ? 1.5 0.25 0.31 0.05 1.30 0.10 3.4 max. 3.4 max [figure 2]
saw filter hdf 1575a s - 6 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 9 of 9 [unit:mm] a b c d e w t r ? 330 1.0 ? 100 0.5 ? 13 0.5 ? 21 0.8 2 0.5 13 0.3 3 max. 1.0 max.
|
